IR Academy · Module 7 · Holding

Holding Pattern (Holding) How to Fly It?

Short answer: A holding pattern is a racetrack-shaped pattern flown around a fix: at the fix turn to the holding side, start the timer when abeam the fix on the outbound leg, and after the time elapses turn back and fly to the fix on the inbound track. The inbound leg should be 1 minute at and below 14,000 ft, and 1.5 minutes above; for wind, the inbound correction is applied three times on the outbound and the outbound time is adjusted.

Final Approach · Updated: 18.11.2026 · Source: ICAO PANS-OPS (Doc 8168) and PANS-ATM (Doc 4444)

Tap and learn

Anatomy of a Holding Pattern

Inbound track 090°, a right-hand (standard) VOR hold. Tap the numbered areas or start the turn.

NON-HOLDING SIDE HOLDING SIDE INBOUND 090° · 1 MIN OUTBOUND 270° XXV ABEAM · START TIMING RATE 1 / 25° TURN D10DME LIMIT MHA 4000 · MAX 230 KT090° · 1 MIN N ↑ · 1 MIN ≈ 3 NM @ 180 kt 123456789
1 / 9

Holding Point (Fix)

The point to which the pattern is tied: a VOR, NDB, RNAV waypoint or VOR/DME intersection. Each circuit begins by passing over the fix.

Note the time you pass the fix; timing and entry are based on it.
ATC

Elements of a Holding Clearance

ATC issues holding instructions in a fixed order. For a published hold, saying "hold as published" is sufficient.

ATC Hold northeast of XXV on the 040 radial, left turns, maintain FL100, expect further clearance at 1435.
ItemExample
FixHold at XXV / Hold at ARMUT
Levelmaintain FL100 / 5000 feet
Side and routenortheast, on the 040 radial / inbound track 220
Turn directionleft turns (for right turns it is usually not stated)
Leg (if non-standard)2 minute legs / 5 NM legs
Expected further clearance (EFC)expect further clearance at 1435
In the cockpit

Fly the Hold Step by Step

  1. Copy clearanceNote the fix, side, radial or inbound track, turn direction, level, leg and EFC time. Find the inbound track (radial + 180).
  2. Determine the entry and slow downBefore reaching the fix, slow to holding speed (230 kt below 14,000 ft) and select the entry type: direct, parallel or teardrop.
  3. Turn at the fixNote the time when passing the fix, then turn in the holding direction using a standard turn and return to the outbound heading.
  4. Start the timer abeamWhen abeam the fix, start the outbound timing; apply three times the wind correction to the outbound heading.
  5. Second turn and inboundWhen time is up, turn, intercept the inbound track, measure the inbound time; adjust the next outbound accordingly.
  6. Report and leaveReport entering the hold; wait for approach or route clearance at the EFC time. In case of radio failure, act according to the EFC.
Calculation

Wind Correction and Outbound Time

Enter the wind: calculate the inbound heading, the outbound heading (rule of three) and the outbound time that will bring the inbound leg to the correct duration. The diagram updates with the wind.

097°inbound heading
249°outbound heading
1:30outbound time
164inbound GS kt

Dashed: pattern without wind · white: track drifted by wind (uncorrected) · arrow: wind. Simple model: drift in the turns is ignored.

Rule of Three

If the inbound leg needs a 5° correction to the right, apply a 15° correction to the left on the outbound. Reason: during the outbound leg and the two turns, the wind keeps pushing you to the same side, so you load the whole correction onto the outbound.

Time Correction

On the first circuit, fly the outbound for the standard time and measure the inbound. If the inbound took 45 s (tailwind), lengthen the outbound by about 15 s; if it took 75 s, shorten the outbound by 15 s. Fine-tune on the second circuit.

Login

Holding Pattern Entry Types

Depending on the aircraft's heading to the fix, there are three entries: direct (≈180° sector), parallel (110°) and teardrop (70°). Rule of thumb: A = heading − inbound track; for right-turn holding, 110°–180° teardrop, 180°–290° parallel, the rest direct.

ICAO PANS-OPS

Speed and Time Limits

Descend before reaching the holding fix, at holding speed. If the chart shows a different limit, that one applies.

AltitudeMax. speedInbound leg
14 000 ft and below230 kt1 min
14 000 – 20 000 ft240 kt1.5 min
20 000 – 34 000 ft265 kt1.5 min
Above 34 000 ftM0.831.5 min

For A/B category aircraft, 170 kt below 14,000 ft. In turbulence, a higher speed may be used with ATC approval.

FAQ

Frequently Asked Questions

What Is a Holding Pattern (Holding)?

A holding pattern is a racetrack-shaped route flown by an aircraft around a holding fix on ATC instruction: inbound leg towards the fix, 180° turn, outbound leg and another 180° turn. It keeps the aircraft in a protected area and at a set altitude while waiting for traffic congestion, bad weather, runway closure or approach sequencing. The standard hold is right-hand.

How to Enter a Holding Pattern?

One of three entry procedures is chosen based on the difference between the aircraft's arrival heading to the fix and the inbound track: direct, parallel or teardrop. For a right-hand hold, if the difference (arrival − inbound) is 110°–180° it is teardrop, 180°–290° it is parallel, and otherwise a direct entry is made. Details and a worked example are on the Holding Entry Procedures page.

When Does the Timing Start in Holding?

Start the outbound timing when you are abeam the fix on the outbound leg. If the abeam point cannot be determined, start it once the turn is complete and the wings are level. Set the outbound time so the inbound leg takes 1 minute at or below 14,000 ft and 1.5 minutes above that.

How to Correct for Wind in the Hold?

Apply three times the wind correction angle (WCA) found on the inbound leg, in the opposite direction, on the outbound. For timing correction, if the inbound leg was short (tailwind), lengthen the outbound; if it was long (headwind), shorten it.

What is EFC?

EFC (Expect Further Clearance) is the time at which ATC plans to issue new clearance to leave the hold. In case of radio failure, the pilot leaves the hold at this time and begins the approach.

What Is Minimum Holding Altitude (MHA)?

The lowest altitude that provides obstacle clearance in the holding area and guarantees communications and navigation coverage. It is written beside the holding symbol on the chart; you may not hold below it.

Is Timing Used in a DME Hold?

No. If the leg is given by distance (e.g. 5 NM legs or D15 limit), the outbound ends when the DME distance is reached. For a hold moving away from the station, the outbound limit is the larger DME value.