Holding Entry Procedures: the full explanation
Published: · Updated: · By: Son Yaklaşma editorial team
Entry sectors summary (right-hand standard hold)
| Entry procedure | Sector width | Relative bearing range | How to fly it? |
|---|---|---|---|
| Direct (direct) | ≈ 180° | 0°–110° and 290°–360° | Cross the fix, then turn directly onto the holding side to enter the outbound leg. |
| Parallel (parallel) | 110° | 180°–290° | Cross the fix, fly parallel to the inbound course on the reciprocal (outbound heading) for approximately 1 minute, then turn towards the holding side and intercept the inbound track. |
| Teardrop | 70° | 110°–180° | Cross the fix, fly on a heading offset 30° towards the holding side for approximately 1 minute, then turn back onto the inbound track. |
For a left-hand (non-standard) hold, the sectors are the mirror image of this. Unless ATC specifies otherwise, the hold is right-handed.
Worked example: which entry?
Hold: inbound course 270°, right-hand (holding side north), outbound course 090°. Relative bearing = aircraft's approach track to the fix − inbound course (if negative, add 360).
| Approach track | Relative bearing | Entry | After the fix |
|---|---|---|---|
| 300° | 300 − 270 = 30° | Direct | Turn right and fly directly onto outbound 090°. |
| 045° | 045 − 270 + 360 = 135° | Teardrop | Offset 30° towards the holding side and fly 060° for 1 minute, turn right and intercept inbound 270°. |
| 180° | 180 − 270 + 360 = 270° | Parallel | Fly outbound 090° on the non-holding side (south) for 1 minute, turn left and return to the fix. |
For a left-hand hold, use the same table by taking 360 − relative bearing instead of the relative bearing.
Holding pattern dimensions
- Turn rate: Standard rate turn (360° per minute, i.e. 3°/sec) or 25° bank angle, whichever requires the lower bank angle, is used.
- Outbound time: 1 minute at or below 14,000 ft, 1.5 minutes above 14,000 ft. Time is measured from crossing the fix on entry and on the outbound leg.
- Inbound course (IC) and outbound course (OC): OC = IC ± 180°.
Common mistakes
- Misreading the sector. For right- and left-hand holds, the parallel and teardrop sectors swap places; always confirm the holding side first.
- Confusing approach track with inbound course. Relative bearing is the difference between the track the aircraft follows as it approaches the fix and the inbound course, not the aircraft's heading.
- Starting the timing late on entry. For parallel and teardrop entries, the 1-minute timing starts after crossing the fix.
In the exam mode of the simulation above, a random heading and inbound course are given; choose the entry procedure yourself and the correct track line will be shown.
How is the holding entry procedure determined?
- Determine the inbound course. Find the inbound course (IC) from ATC or the procedure chart. This is your approach track to the holding fix.
- Calculate arrival direction. Note the aircraft's current heading. Calculate the difference between the arrival direction and the inbound course.
- Learn holding direction. ATC specifies whether a right-turn (standard) or left-turn (non-standard) hold is required. Standard hold is right-turn.
- Determine the sector. Right-turn hold: relative bearing 0°–110° and 290°–360° means direct, 180°–290° means parallel, 110°–180° means teardrop entry.
- Apply entry. As you approach the holding fix, apply the entry procedure you selected (direct, parallel or teardrop) and join the holding pattern.
Frequently asked questions
What are the holding entry procedures?
According to ICAO procedures there are three holding entry procedures: direct entry, parallel entry and teardrop entry. Which procedure to apply is determined by the angle between the aircraft's arrival direction to the holding fix and the inbound course.
When is direct entry applied?
In a right-hand hold, if the aircraft's arrival track relative to the inbound course lies in the 0°–110° and 290°–360° sector (about 180° in total), a direct entry is used. The aircraft crosses the fix and turns directly towards the holding side to enter the outbound leg.
When is parallel entry applied?
In a right-hand hold, if the aircraft's arrival track relative to the inbound course lies in the 180°–290° sector (110° wide, the side where the holding pattern is), a parallel entry is used. The aircraft crosses the fix, flies the reciprocal of the inbound course (outbound direction) for approximately 1 minute, then turns towards the holding side and intercepts the inbound track.
When is teardrop entry applied?
In a right-hand hold, if the aircraft's arrival track relative to the inbound course lies in the 110°–180° sector (70° wide, the opposite side of the holding pattern), a teardrop entry is used. The aircraft crosses the fix, flies for approximately 1 minute on a heading offset 30° towards the holding side, then turns to intercept the inbound track.
How do sectors change in a left-turn hold?
In a left-turn (non-standard) hold, the sectors are the mirror image of those in a right-turn hold. The parallel entry sector moves to the right side, and the teardrop sector moves to the left side.
What are inbound course and outbound course?
The inbound course (IC) is the magnetic track the aircraft follows as it approaches the holding fix. The outbound course (OC) is the exact reciprocal of the inbound course (IC + 180°); the aircraft follows this track on the outbound leg. In the holding pattern the aircraft continually alternates between the inbound and outbound legs.
How many minutes does the outbound leg last in the holding pattern?
According to ICAO PANS-OPS, the outbound leg is 1 minute at 14,000 ft and below, and 1.5 minutes above 14,000 ft. Time is measured after passing the fix on entry and on the outbound leg.
At what speed are turns made in the holding pattern?
Turns are made at standard rate (360° per minute, i.e. 3°/s) or at 25° bank angle; whichever requires the lower bank angle is used.
Sources
- ICAO Doc 8168 (PANS-OPS), Volume I: holding procedures and entry methods
- FAA, Aeronautical Information Manual (AIM): Holding