IR Academy · Module 1 · Fundamentals

IFR Basics

Short answer: IFR (Instrument Flight Rules) is flight conducted by looking only at instruments without seeing outside, under an ATC clearance and minimum altitudes. It rests on three skills: instrument scanning (centred on the artificial horizon), copying the clearance correctly (CRAFT), and applying the standard procedure in an unexpected situation (e.g. radio failure).

Final Approach · Updated: 18.11.2026 · Source: SERA (EU 923/2012), ICAO Doc 4444

Weather or rule?

VMC, IMC, VFR and IFR

Explains VMC and IMC weather, and VFR and IFR rules. If visibility and distance from cloud are below the VMC minima below, the weather is IMC and only IFR may be flown.

RegionFlight visibilityDistance from cloud
FL100 and above (Class B–G)8 km1500 m horizontal, 1000 ft vertical
Below FL100, above 3000 ft AMSL or above 1000 ft AGL5 km1500 m horizontal, 1000 ft vertical
3000 ft AMSL / 1000 ft AGL and below (Class F, G)5 kmCloud-free and with the ground in sight

SERA.5001 VMC minima (Europe). States may allow some exceptions at low altitude; check the AIP.

Tap and learn

Six Basic Flight Instruments

The classic "six pack" panel. Tap an instrument: see what it shows, which system it works with and what to do in a failure. In a glass cockpit (PFD) the same information is shown on a single screen.

KNOTS 0123456789 1013 ALT LR 2 MIN N36E1215S2124W3033 011UPDN x1000 FT/MIN 123456

Yellow dashed lines show the instrument scan: each glance returns to the artificial horizon.

1 / 6

Airspeed Indicator (ASI)

Using the difference between pitot (dynamic) and static pressure, the instrument shows indicated airspeed (IAS). Coloured arcs: white flap range, green normal operating range, yellow caution (in calm air only), red line the speed never to be exceeded (VNE).

If the pitot tube is blocked and the drain hole is also blocked, the ASI behaves like an altimeter: the airspeed appears to increase while climbing.
Skill

Instrument Scan

The most common error in instrument flying is fixating on a single instrument (fixation). Correct scanning is continuous, regular and centred on the artificial horizon.

Artificial Horizon Centred

First set the attitude (pitch and bank) on the artificial horizon, then check the result on the performance instruments: altimeter, heading, airspeed.

Three Typical Errors

Fixation (looking at a single instrument), omission (never checking an instrument) and overemphasis (relying too much on one instrument). All of them lead to gradual deviations.

Varies With Manoeuvre

In level flight, scan the altimeter for altitude and the heading indicator for heading; in turns, the turn coordinator and heading; in climbs, the airspeed indicator is scanned more often.

In the cockpit

CRAFT Clearance Trainer

Copy an IFR clearance using five letters: Clearance limit, Route (route/SID), Altitude (initial altitude), Frequency (departure frequency), Transponder (squawk). Read the clearance and find the information requested.

CClearance limit
RRoute / SID
AAltitude
FFrequency
TTransponder
0True
0Series
—Best streak
SSR

Transponder Codes

ATC assigns every IFR flight a squawk code. The special codes below mean the same thing everywhere in the world and trigger an alarm on the ATC screen as soon as they are selected.

CodeMeaning
7500Unlawful interference (hijacking)
7600Radio communication failure
7700Emergency
7000VFR flight (general code in Europe)
2000IFR flight with no SSR code assigned (ICAO)

When changing codes, take care not to display 7500, 7600 or 7700 by mistake as an intermediate value.

ICAO Doc 4444

Radio Failure Procedure

Radio failure in IMC is one of the most frequently asked IFR topics. Goal: be able to predict what ATC expects you to do.

  1. Transponder 7600First check the radio, headset and frequency; then squawk 7600. If ATC can see you on radar, they may give instructions by transponder or light.
  2. If you are in VMCStay in VMC, land at the nearest suitable aerodrome and inform ATC as soon as possible.
  3. If you are in IMC, wait firstIn a radar environment, keep the last assigned speed and level for 7 minutes (20 minutes without radar), or the minimum flight altitude if higher.
  4. Then return to the flight planMeet the level and speed in the flight plan and continue on track; if you are being vectored, rejoin the flight plan route by the shortest way.
  5. On arrivalGo to the facility serving the destination aerodrome; hold if necessary. Begin descent at the expected approach or arrival time, carry out the instrument approach and, if possible, land within 30 minutes.

AIPs may differ between countries (e.g. US FAA rules differ). Before flight, check the destination country's radio failure procedure.

Flight Rules in the Flight Plan

  • I: whole flight IFR
  • V: whole flight VFR
  • Y: IFR first, then VFR
  • Z: VFR first, then IFR

Altimeter Settings

  • QNH: altitude above mean sea level; below transition altitude, take-off, approach and landing.
  • 1013 hPa (standard): when climbing through the transition altitude; flight level (FL) is read.
  • QFE: shows 0 at aerodrome level; used in some countries and in military flying.
FAQ

Frequently Asked Questions

What Is the Difference Between IFR and IMC?

IMC (Instrument Meteorological Conditions) is a weather condition: visibility or distance from cloud is below the VMC minima. IFR (Instrument Flight Rules) is a set of rules: flight under a flight plan, ATC clearance and minimum altitudes. Only IFR may be flown in IMC; IFR flight may also be conducted in VMC.

How to Perform an Instrument Scan?

The most common method is the "radial" scan with the attitude indicator at the centre: the eyes move from the attitude indicator to one instrument and back. Which instruments you check more often is determined by the manoeuvre; for example, in level flight the altimeter for altitude and the heading indicator for heading.

What Does CRAFT Mean?

The order used to note an IFR clearance: Clearance limit (usually the destination aerodrome), Route (or SID), Altitude (initial altitude), Frequency (departure frequency) and Transponder (squawk code).

Which Code Is Squawked in a Radio Failure?

7600 is radio failure. 7500 is for unlawful interference, 7700 for emergencies. In radio failure the ICAO procedure applies; in a radar environment, keep the last assigned level and speed for 7 minutes, then proceed according to the flight plan.

What Do I, V, Y and Z Mean in a Flight Plan?

Flight rules field (item 8): I means entirely IFR, V entirely VFR, Y IFR first then VFR, Z VFR first then IFR.