VOR Navigation: Intercept the Radial: the full explanation
Published: · Updated: · By: Son Yaklaşma editorial team
What is a VOR?
VOR (VHF Omnidirectional Range) is a radio navigation aid that transmits 360 separate bearing indications (radials) relative to magnetic north from a ground station. The station transmits two 30 Hz signals: one reference signal that is in phase in every direction, and one variable signal whose phase changes with direction. The receiver in the aircraft finds which radial the aircraft is on from the phase difference between the two. The VOR operates in the 108.00–117.95 MHz VHF band; because the signal travels in line of sight, range depends on altitude (approximately 1.23 × √altitude(ft) NM).
A radial is always a direction outward from the station and is measured relative to magnetic north. R-090 is the radial east of the station; an aircraft on this radial flies to the station on heading 270. The radial the aircraft is on is called the QDR, and the magnetic direction from the aircraft to the station is called the QDM; there is always 180° between them. Every VOR identifies itself with a three-letter Morse code (ident); the pilot confirms the station by listening to this sound before using it.
How to read the CDI
| Part | What it shows |
|---|---|
| OBS (Omni Bearing Selector) | The knob that selects the course you want to fly. The indicator's card turns to this value. |
| Needle (CDI) | Shows which side of the selected course the aircraft is on. If the needle is to the right, the course is to the right. |
| Dots | On a VOR each dot is 2', and full needle deflection is 10'. If the needle is against the stop, you are at least 10' from the course. |
| TO / FROM | If you fly the selected course, whether you are going to the station (TO) or moving away from it (FROM). |
| OFF (NAV) flag | No signal or unreliable signal: out of range, directly over the station (cone of confusion) or at the TO/FROM boundary (abeam). |
The most important rule is: the CDI and the TO/FROM flag are independent of the aircraft's heading, and depend only on the aircraft's position relative to the station and the OBS setting. If the aircraft turned on the spot, the indication would not change. The flag shows TO or FROM depending on which side of the perpendicular line drawn through the station to the course selected on the OBS the aircraft is on; exactly on this line (abeam) it shows OFF.
Which OBS, which flag?
| Task | OBS | Flag | Note |
|---|---|---|---|
| Inbound on R-090 | 270 | TO | The flying heading to the station is the reciprocal of the radial. |
| Outbound on R-090 | 090 | FROM | The radial itself is selected. |
| Inbound on R-240 | 060 | TO | 240 + 180 = 420 → 060. |
| Outbound on R-360 | 360 | FROM | Moving away from the station to the north. |
Reverse sensing
When the aircraft's heading is close to the course selected on the OBS, the needle works on the principle of “turn towards the needle”. If the heading is close to the reciprocal of the selected course, the needle works in reverse: turning towards the needle takes the aircraft further off course. For example, if you fly to the station on heading 060 on R-240 and leave the OBS at 240, the flag shows FROM; when the aircraft drifts to R-245, the needle deflects to the left even though the selected course is to the right. The solution is simple: set the OBS close to the direction you are flying (here 060, TO).
Cone of confusion
Directly over the station, the signal is unstable in a cone-shaped area: the needle oscillates, the flag briefly shows OFF, and after passing the station it changes from TO to FROM. Keep the heading steady during this time and do not chase the needle. Because DME measures slant range, it shows the aircraft's altitude directly over the station (approximately 1 NM at 6000 ft).
The 1 in 60 rule
At 60 NM, a 1° angle corresponds to approximately 1 NM of lateral distance. Accordingly, the deflection on the CDI means different distances depending on the distance from the station: when far from the station, one dot corresponds to several kilometres; as you get closer, the needle becomes much more sensitive.
| Distance from station | 1 dot (2°) | Full deflection (10°) |
|---|---|---|
| 10 NM | ≈ 0.3 NM | ≈ 1.7 NM |
| 20 NM | ≈ 0.7 NM | ≈ 3.3 NM |
| 30 NM | ≈ 1.0 NM | ≈ 5.0 NM |
| 60 NM | ≈ 2.0 NM | ≈ 10.0 NM |
How to read the RMI
On the RMI (Radio Magnetic Indicator), the card rotates together with the aircraft's magnetic heading; the marker at the top is the current heading. The head of the needle shows the station (QDM), and the tail shows the radial the aircraft is on (QDR). The RMI has no OBS, and the needle always points to the station; that is why the tail is the quickest answer to “which radial am I on?”.
How to read the HSI
The HSI (Horizontal Situation Indicator) combines a heading indicator and a CDI in a single instrument. The card rotates with the aircraft's heading; the arrow on it shows the selected course (CRS, the equivalent of the OBS on the CDI). The deviation bar in the middle of the arrow shows deviation from the course on the same scale as the CDI needle (full deflection 10°, 2° per dot); the TO/FROM triangle also rotates with the arrow. Because the arrow rotates with the card, the picture on the indicator is a bird's-eye view of the real situation: if the bar is to the right of the aircraft symbol, the course really is to the right. For this reason there is no reverse sensing on the HSI; even if the heading is reciprocal to the selected course, the bar still shows the correct side of the course.
How to fly a DME arc
A DME arc is an arc-shaped track flown around a station at a constant DME distance (e.g. 10 NM); it is used in instrument approaches to transition between radials. When approaching the station on a radial, at around 120 kt, turn 90° about 0.5 NM before the arc distance. On the arc, the station should be at the wingtip: the RMI needle shows RB 090 or 270. In straight flight the needle moves behind the wingtip and the DME increases; when the needle drops back 5–10°, turn about 10° towards the station. If the DME is greater than the arc distance, make small corrections towards the station; if it is smaller, make them outward. If the exit radial is set on the OBS, the time to leave the arc has come when the CDI centres.
Worked example
The aircraft is on R-250, 25 NM from the station. Task: fly inbound to the station on R-240.
- OBS: 240 + 180 = 060. Because the aircraft is on the TO half of the station, the flag shows TO.
- Needle: The aircraft is 10° away from the target radial, and the needle rests to the right. Using the 1 in 60 rule, the lateral distance is 25 × 10 / 60 ≈ 4.2 NM.
- Intercept heading: The needle is to the right, so the route is to the right. At a 45° angle: 060 + 45 = 105.
- Time: For a 4.2 NM lateral distance on a 45° intercept, about 5.9 NM of track is needed; at 120 kt, about 3 minutes.
- Return to the route: When the needle starts to move (once it is within 10°), reduce the heading and turn back to 060; if there is wind, add a correction into the wind.
Common mistakes
- Confusing the radial with the heading. To fly to the station on R-240, the heading is 060, not 240.
- Not checking the flag. If you see FROM on an inbound track, either you have passed the station or the OBS is wrong.
- Falling into reverse sensing. If you do not set the OBS close to your direction of flight, the needle will take you off course.
- Chasing the needle over the station. Keep the heading steady in the cone of confusion and re-check once you have passed the station.
- Not listening to the identification code. A VOR under maintenance may not transmit its ident or may transmit a TEST code; a station whose ident cannot be heard is not used.
The default station (SYK 113.40) is fictional; a real Turkish VOR can be selected from the list (OurAirports open data; the AIP Türkiye is authoritative for current and official information). The map is oriented to magnetic north; on a real station, aerodromes are drawn rotated by the station's magnetic variation. The OFF zone is represented as ±3° of abeam, and the cone of confusion as 0.8 NM around the station. For training purposes only.
How is a VOR radial intercepted and tracked?
- Set and identify the station. Enter the frequency and listen to the Morse identification code to confirm you have the correct station.
- Set the OBS. If you are flying inbound to the station, the radial + 180°; if flying outbound from the station, the radial itself. The flag should show TO inbound and FROM outbound.
- Look at the needle side. The selected course is on the side the needle is on.
- Get intercept heading. Turn 30–45° towards the needle side relative to the course; for example, if the course is 060 and the needle is to the right, heading 090–105.
- Return to track. When the needle starts to centre, turn to the course; if there is wind, add a correction into the wind.
- Watch. Make small heading corrections to keep the needle centred; the flag changes over the station, so keep the heading steady.
Frequently asked questions
What is a VOR radial?
A radial is the magnetic bearing from the VOR station outward, measured relative to magnetic north. R-090 is the line east of the station; to fly inbound on this radial, the heading is 270.
What is the difference between QDM and QDR?
QDR is the magnetic bearing from the station to the aircraft, i.e. the radial the aircraft is on. QDM is the magnetic bearing from the aircraft to the station. There is always a 180° difference between them: for an aircraft on R-240, QDM is 060.
How many degrees is one dot on the CDI?
On a VOR, each dot is 2° and full-scale deflection is 10°. With the 60 to 1 rule, one dot corresponds to about 1 NM lateral offset at 30 NM from the station, and about 2 NM at 60 NM.
What does the TO/FROM flag depend on?
It depends on which side of the perpendicular line drawn through the station to the course selected on the OBS the aircraft is on. If flying the selected course takes you towards the station it shows TO; if it takes you away it shows FROM; on the perpendicular line it shows OFF. The aircraft's heading does not affect the flag.
What is reverse sensing?
Reverse needle behaviour occurs when the aircraft's heading is close to the reciprocal of the course selected on the OBS: turning towards the needle moves the aircraft away from the course. The problem disappears when the OBS is set close to the direction being flown.
What is the cone of confusion?
This is the cone-shaped area directly above the VOR station. The signal is unstable here: the needle swings, the flag shows OFF, and it changes from TO to FROM after passing the station. Keep the heading steady during this time and do not chase the needle.
What is the difference between RMI and CDI?
The CDI shows deviation from the course selected on the OBS and is independent of the aircraft's heading. On the RMI the card rotates with the aircraft's heading; the needle head points to the station (QDM) and the tail shows the radial being flown (QDR), and no OBS setting is required.
What is the difference between HSI and CDI?
The CDI only shows deviation from the selected course and does not know the aircraft's heading; if the heading is reversed relative to the course, the needle works in reverse. On the HSI the card rotates with heading and the course arrow rotates with it, so the deviation bar shows the true position of the course relative to the aircraft and reverse sensing does not occur.
When is the DME arc flown?
When approaching the station on the radial, turn 90° at about 120 kt, approximately 0.5 NM before the arc distance (about 10.5 DME for a 10 DME arc). The turn is started earlier as speed increases because the turn radius grows.
On which frequencies does a VOR transmit?
In the 108.00–117.95 MHz VHF band. The 108.00–111.95 MHz range is shared with ILS localisers; localisers use frequencies with an odd tenths digit in this range (such as 108.10 and 108.30). Because VHF propagates by line of sight, range depends on altitude.
Are my results being saved?
The simulator is open to everyone. To see "Where am I?" tour scores and mission stars, it is enough to sign up for free and log in.
Sources
- FAA, Pilot's Handbook of Aeronautical Knowledge, Chapter 16: Navigation
- FAA, Aeronautical Information Manual, Chapter 1 Section 1: Navigation Aids
- ICAO Annex 10, Aeronautical Telecommunications, Volume I: Radio Navigation Aids
- OurAirports open data (navaids)