V2

PPLATPL Performance
IN SHORT

V2 is the minimum speed required during take-off to allow the aircraft to climb safely after a critical engine failure.

What is V2?

V2 (Take-Off Safety Speed) is a critical speed defined in the take-off performance calculations of multi-engine aircraft and published in the AFM. If an engine fails at or above this speed, the pilot may continue the take-off and climb with the required obstacle clearance margin (35 feet). V2 varies with aircraft weight, air density, runway slope, wind and flap setting.

V2 lies between V1 (decision speed) and VFTO (final take-off speed). If an engine failure occurs after V1, the pilot must continue the take-off and climb while maintaining V2. If the aircraft is below V2, it may not achieve the required climb performance and there is a risk of striking obstacles.

In performance calculations, the V2 value is taken from the AFM and used in flight planning for take-off distance, obstacle clearance height and climb performance calculations. The pilot must know V2 before take-off and take it into account during the take-off.

Example

In a Boeing 737 take-off: MTOW 70,000 kg, temperature 25°C, runway elevation 500 ft, flaps 5°. From the AFM, V1 = 145 kt, V2 = 155 kt and VFTO = 160 kt are determined. If the left engine fails at 150 kt during the take-off (after V1), the pilot must continue the take-off and climb while maintaining V2 (155 kt).
TEST YOURSELF

What risk arises if the aircraft is flown below V2 following an engine failure?

How it is asked in the ATPL exam: 3 questions

Think about your answer, then reveal it.

1. For a jet aeroplane, V2 is defined as the _____ speed, measured at the point when the aircraft reaches 35 feet above the runway.

  1. lift off speed.
  2. critical engine failure speed.
  3. take-off climb speed or speed at 35 ft.
  4. take-off decision speed.
Show answer

Correct answer: take-off climb speed or speed at 35 ft.

V2 is the take-off climb speed—the minimum speed the aircraft must maintain during the initial climb after engine failure; it is measured at 35 ft height to standardize the definition.

2. If the pilot selects take-off flaps 20° instead of take-off flaps 10°, how is V2 affected?

  1. V2 decreases if not restricted by VMCA.
  2. V2 has no connection with T/O flap setting, as it is a function of runway length only.
  3. V2 has the same value in both cases.
  4. V2 increases in proportion to the angle at which the flaps are set.
Show answer

Correct answer: V2 decreases if not restricted by VMCA.

Greater flap deflection increases lift at a given speed, allowing a lower V2; however, if VMCA becomes the limiting factor at higher flap angles, V2 may not decrease as much as expected.

3. You are preparing a take-off performance calculation. The aircraft mass is higher than planned. How will this affect the rotate speed VR and the take-off safety speed V2?

  1. It will increase VR but decrease V2
  2. It will decrease both speeds
  3. It will increase both speeds
  4. It will decrease VR but increase V2
Show answer

Correct answer: It will increase both speeds

Higher aircraft mass requires higher airspeed to generate enough lift for rotation and to maintain the required climb gradient. Both VR and V2 increase with mass.

Solve 10 free questions from this subject →

Frequently asked questions about V2

What is the difference between V2 and V1?

V1 is the speed at which the decision to stop or continue the take-off is made; V2 is the minimum take-off safety speed required to climb safely following a critical engine failure.

Which factors affect V2?

V2 varies with aircraft weight, air density, runway slope, wind and flap setting, and is taken from the AFM.

Machine-translated (AI) from our Turkish glossary entry using ICAO/EASA terminology. Updated 1 Nov 2026 · Report an error: [email protected]