IR Academy · Module 2 · Equipment

Radio Navigation Equipment

Short answer: VOR gives bearing (radial), DME gives distance, NDB gives bearing; ILS provides lateral and vertical guidance to the runway, while GNSS provides position by satellite. VOR, DME and ILS work on line of sight; NDB, being low frequency, does not need line of sight but is affected by night and thunderstorms.

Final Approach · Updated: 18.11.2026 · Source: ICAO Annex 10

Facility by facility

How Do They Work?

VOR

108.00–117.95 MHz (VHF)
Working principle
It transmits two 30 Hz signals: a reference signal in phase in all directions, and a signal whose phase changes with direction. The receiver finds the magnetic direction (radial) from the station by the phase difference between the two signals.
В кабине
On the CDI/HSI, deviation from the selected course and the TO/FROM flag; on the RMI, bearing to the station.
Errors and limits
Line-of-sight range; cone of confusion directly over the station; reflections over mountainous terrain.
Try in simulator

DME

962–1213 MHz (UHF)
Working principle
The aircraft sends an interrogation signal and the ground station replies after a fixed delay. Distance is calculated from the round-trip time. It is usually paired with VOR or ILS, and the frequency is tuned automatically.
В кабине
Distance in NM; ground speed and time to the station from successive measurements.
Errors and limits
Gives slant range: directly over the station it shows a distance equal to altitude. Line-of-sight range.

NDB / ADF

190–1750 kHz (LF/MF)
Working principle
A simple transmitter broadcasting in all directions. The ADF in the aircraft uses loop and sense antennas to find the direction of the incoming signal and the needle points to the station.
В кабине
On the ADF, relative bearing; on the RMI, magnetic bearing (QDM).
Errors and limits
Night effect, coastal refraction, thunderstorms (the needle swings towards the CB), mountain effect, bank error. No line of sight needed, and it is received at low altitude too.
Try in simulator

ILS

LOC 108,10–111,95 MHz · GS 329–335 MHz
Working principle
The localiser radiates two lobes modulated at 90 Hz and 150 Hz on either side of the runway centreline; the receiver determines left-right deviation from which lobe dominates. The glide slope works on the same principle to give up-down deviation (usually 3°).
В кабине
LOC and GS needles (or diamonds on the PFD); distance from DME or marker.
Errors and limits
False indications outside the coverage area; false glide path on the glide slope; signals distorted by vehicles or aircraft within the ILS critical area.
Try in simulator

GNSS

L band (≈1.2–1.6 GHz)
Working principle
The receiver calculates its own position from the travel time of signals from several satellites. Integrity is provided by RAIM (the receiver self-checks using extra satellites) or by SBAS (EGNOS/WAAS).
В кабине
FMS/GPS display shows track, distance, groundspeed; lateral and vertical deviation on RNP approach.
Errors and limits
RAIM outage when satellite geometry is weak; jamming and spoofing; database errors.
через 5 с

Which Facility Is This Frequency For?

When entering a frequency in the cockpit, you must know which equipment you are tuning. Rule: if kHz, NDB; between 108–112 MHz, localiser if the decimal is odd, VOR if even; above 112 MHz, VOR.

0Верно
0Серия
—Лучшая серия
Расчёт

VHF Range and DME Slant Range

VHF Line-of-Sight Range

148NM range
123aircraft share NM
25station share NM

Range ≈ 1.23 × (√aircraft altitude + √station elevation). Terrain obstacles and transmitter power may shorten the range.

DME Slant Range → Ground Distance

1,5NM ground distance
2,0NM height
%51difference

Ground distance = √(DME² − height²), height in NM (ft ÷ 6076). The difference shrinks as you move away from the station.

Итоги

All Facilities in One Table

EquipmentИнформация предоставленаTypical rangeИспользование
VORDirection (radial)Line of sight, up to ~200 NMAirways, VOR approach, holding
DMEDistance (slant)Line of sight, up to ~200 NMDistance fixes, DME arcs
NDBDirection (bearing)Usually 25–100 NM (depending on power)NDB approach, locator, holding
ILSLateral + vertical deviationLOC 25 NM (±10°), GS 10 NMPrecision approach
GNSSPosition (3D)GlobalRNAV/RNP routes and approaches

Ranges are typical; each facility's service volume is stated in the AIP.

FAQ

Часто задаваемые вопросы

What Is the Difference Between a VOR Radial and an NDB Bearing?

The VOR radial is the magnetic direction outward from the station and is independent of the aircraft's heading. ADF, however, shows the bearing relative to the aircraft's nose; for magnetic bearing to the station (QDM), heading is added: QDM = heading + relative bearing.

Why Does DME Show Slant Range?

DME measures the straight-line distance between the aircraft and the station. When flying high, this distance is slightly longer than the horizontal distance on the ground; directly over the station, DME shows a distance equal to the aircraft's altitude (e.g. 6000 ft ≈ 1 NM). The difference becomes negligible further from the station.

How Is VHF Range Calculated?

VHF signals propagate along line of sight. Approximate range (NM) = 1.23 × √(aircraft altitude ft) + 1.23 × √(station elevation ft). For example, at 10,000 ft you can receive a sea-level station from about 123 NM.

How to Tell a Localiser from a VOR Frequency?

Frequencies in the 108.00–111.95 MHz range with an odd decimal (108.10; 109.30; 110.30…) are ILS localisers; even ones are VORs. 112.00 MHz and above are VOR only.

What Is RAIM?

RAIM (Receiver Autonomous Integrity Monitoring) is the GNSS receiver's ability to detect a faulty satellite by itself, using extra satellites. At least 5 satellites are needed to detect a fault and at least 6 to exclude the faulty satellite. The RAIM prediction is checked before an RNP approach.