VDF
VHF Direction Finding
VDF (VHF Direction Finding) is a radio direction-finding system that allows a ground station to determine the bearing of an aircraft from its VHF radio transmissions. ATC uses it to establish aircraft position and heading.
What is VDF?
VDF (VHF Direction Finding) is a radio direction-finding system operating in the VHF band (approximately 118–137 MHz). The VDF receiver at the ground station measures the direction from which the aircraft's radio transmission arrives and calculates this direction as a bearing relative to the station. The system works effectively when there is line of sight between the aircraft and the ground station; therefore, measurement accuracy may decrease at low altitude or behind obstacles.
Its main use is air traffic control (ATC). The controller obtains bearing information from the pilot's radio transmission using VDF and can use this information to determine the aircraft's position or give the pilot a heading. A position fix can be obtained by intersecting the bearing information received from the same aircraft by two or more VDF stations. This capability helps with position determination in areas outside radar coverage and in emergencies.
From the pilot's perspective, VDF is not a device on the aircraft; it is a system operating on the ground. With VDF support, the pilot may be given headings or may receive bearing information on request. Measurement accuracy and operating procedures vary from country to country and according to the station network; details are specified in the relevant country's AIP publications and ATC procedures.
Often confused with
| Characteristic | VDF | ADF |
|---|---|---|
| Operating band | VHF (approximately 118–137 MHz) | LF/MF (approximately 190–1750 kHz) |
| Signal measured | Aircraft radio transmission (pilot's speech) | Transmission from NDB ground station |
| Measurement performed by | Ground station (ATC) | ADF receiver on board the aircraft |
| Information provided | Bearing of the aircraft relative to the station | Bearing relative to the NDB station |
What is the basic output of the VDF system?
VDF allows the ground station to measure the direction from which the aircraft's radio transmission arrives; on its own it does not provide distance.
How it is asked in the PPL exam: 3 questions
Think about your answer, then reveal it.
1. You are receiving a VDF service from a ground station. What Q-code should you use to request the magnetic bearing FROM the station to your aircraft?
- “Request QDR”.
- “Request QDM”.
- “Request QNH”.
- “Request QTE”.
Show answer
Correct answer: “Request QDR”.
QDR is the Q-code for magnetic bearing FROM the station. QDM is magnetic bearing TO the station, and QTE is true bearing FROM the station.
2. Complete the following: The Q-code for a true bearing TO a VDF station is _____; the Q-code for a magnetic bearing TO a VDF station is _____.
- QDR/QDM
- QTE/QUJ
- QDM/QUJ
- QUJ / QDM
Show answer
Correct answer: QUJ / QDM
QUJ is true bearing TO the station; QDM is magnetic bearing TO the station. QDR and QTE are both FROM-the-station bearings.
3. Which statement about VDF Q-codes is incorrect?
- QTE - true bearing FROM the station
- QDM - magnetic bearing TO the station
- QDR - true bearing TO the station
- QDR - magnetic bearing FROM the station
Show answer
Correct answer: QDR - true bearing TO the station
QDR is a magnetic bearing FROM the station, not a true bearing TO it. QDM is correctly magnetic bearing TO the station, and QTE is correctly true bearing FROM the station.
Frequently asked questions about VDF
What is the difference between VDF and ADF?
VDF (VHF Direction Finding) is the system in which a ground station measures the bearing of an aircraft from its VHF radio transmissions. ADF is the system in which the receiver on the aircraft takes a bearing on an NDB transmission; VDF operates on the ground, while ADF operates in the aircraft.
How does VDF work?
VDF measures the direction from which the aircraft's radio transmission arrives at the ground station, using several antennas or the Doppler method. The measured bearing is used by ATC; VDF on its own does not provide the aircraft's distance.
Machine-translated (AI) from our Turkish glossary entry using ICAO/EASA terminology. Updated 1 Nov 2026 · Report an error: [email protected]