Top of Descent (TOD) Simulation

When must you start descending from cruise altitude to the target fix on a 3° slope? Change altitude, groundspeed and slope; see the top of descent point (TOD), the required rate of descent and how far above the path you will be if you are late.

IRATPLIFRIntermediate level
In short: When should descent begin?

At a 3° gradient, roughly 3 NM is needed for every 1,000 ft of altitude lost (3:1 rule): TOD distance ≈ (altitude to lose ÷ 1,000) × 3 NM. The required rate of descent is approximately ground speed × 5 ft/min (for 3° the exact value is ≈ GS × 5.3). For example, descending from FL100 to 2,000 ft means losing 8,000 ft: TOD is about 24 NM before the fix and at a ground speed of 120 KT approximately 600–640 ft/min is required.

10 000 ft
3 000 ft
120 KT
Descent angle
Extra allowance (deceleration, configuration)
40 NM
Preset scenarios
TOD distance
—NM
Required dive speed
—ft/min
Descent time
—min
Position status
—
—

Descent profile

Target fix to the right, distance to the left

Dive speed relative to ground speed

Required ft/min at constant slope
Height to be lost
—
ft · actual − target
Slope gradient
—
3:1 rule
—
5 × GS rule
—

How does it work?

Descent distance is found from the height to be lost and the gradient: at a 3° gradient, about 3 NM for every 1,000 ft (3:1 rule). The required rate of descent depends on groundspeed: about GS × 5 ft/min (exact value for 3° is GS × 5.3).

The simulation assumes constant groundspeed and constant gradient. ATC altitude and speed restrictions, wind changes and aircraft-specific descent performance are also considered in real planning.

Test yourself

For an aircraft descending from FL100 to 2,000 ft at a groundspeed of 120 KT, how many NM before the fix should descent begin? Estimate using the 3:1 rule, then check in the simulation.

Practice ATPL questions →

This simulator is for training only. Values are representative and do not replace the aircraft’s official POH/AFM, the AIP or current weather information in real flight operations. The pilot in command is always responsible.

Top of Descent (TOD) Simulation: the full explanation

Published: · Updated: · By: Son Yaklaşma editorial team

What is TOD (Top of Descent)?

Top of descent (TOD) is the point where you must begin descending from cruise altitude. The aim is to reach the target fix (e.g. the IAF or the approach starting altitude) at exactly the required altitude, on a stable gradient and at a reasonable descent speed. If you start too early you will fly low and slow unnecessarily; if you start too late, a steep descent, high descent rate and an unstable approach become unavoidable.

Formulas and practical rules

The simulation assumes constant ground speed and constant gradient; in real flight, altitude restrictions, ATC instructions, speed restrictions and the aircraft's performance data take precedence.

Table: TOD distance by altitude to lose

Distance from the fix (NM) by altitude to lose at 3°
Altitude to lose (ft)Exact calculation (NM)3:1 rule (NM)Difference
1,0003.13.0−4%
2,0006.36.0−4%
5,00015.715.0−4%
10,00031.430.0−4%
20,00062.860.0−4%
30,00094.290.0−4%

Table: required descent rate by ground speed

Required descent rate (ft/min) by ground speed and gradient
Ground speed (KT)2.5°3°3.5°5 × GS rule
80354425496400
100442531619500
120531637743600
150663796929750
2501,1051,3271,5481,250
3501,5481,8582,1681,750
4501,9902,3882,7872,250

Table: sample descents

Sample descents at 3°
DescentGround speedTOD (NM)Descent rate (ft/min)Time (min)
6,500 → 2,500 ft100 KT12.65317.5
FL100 → 2,000 ft120 KT25.163712.6
FL100 → 4,000 ft140 KT18.87438.1
FL250 → 5,000 ft300 KT62.81,59212.6
FL350 → 10,000 ft450 KT78.52,38810.5

Worked example

Cruise at FL100, target 2,000 ft, ground speed 120 KT, gradient 3°. Altitude to lose is 8,000 ft. Exact calculation: 8,000 ÷ 318.4 ≈ 25.1 NM; 3:1 rule 8 × 3 = 24 NM. Descent rate: 120 × 5.3 ≈ 637 ft/min (5 × GS rule 600). Time ≈ 12.6 min. If you add +5 NM for slowing down, TOD ≈ 30 NM. If the aircraft is still at cruise altitude 20 NM from the fix, it is about 1,631 ft above the profile and a gradient of ≈ 3.8° is needed to reach the target.

Common mistakes

How do you plan a descent?

  1. Find the altitude difference. Subtract the target altitude from the cruising altitude.
  2. Calculate the distance. At a 3° gradient, divide the difference by 1,000 and multiply by 3 (3:1 rule).
  3. Add share. Add a few NM for deceleration and configuration.
  4. Find the descent speed. Multiply ground speed by 5 (for 3°, approx. ft/min).
  5. Check the time. Divide the distance by ground speed, multiply by 60.
  6. Track position. During descent, check distance and altitude to correct whether you are above or below the profile.

Frequently asked questions

What is TOD (top of descent)?

Top of descent is the point where descent from cruise altitude should begin. It is calculated a certain distance before the target fix so that you reach the fix at the required altitude, with a stable gradient and a reasonable descent speed.

How is the TOD distance calculated?

At 3° the 3:1 rule is used: divide the altitude to lose by 1,000 and multiply by 3. For example, for 8,000 ft, 24 NM. Full calculation: distance = altitude to lose ÷ (tan γ × 6,076 ft/NM).

What is the 3:1 rule?

On a standard 3° descent, you cover about 3 NM for every 1,000 ft of altitude lost. The exact value is 3.14 NM, so the rule falls about 4–5% short; it is accurate enough for practical planning.

How is the required rate of descent (ft/min) found?

Practical rule: ground speed × 5. Full calculation: GS × 101.3 × tan γ; for 3° approximately GS × 5.3. For example, at 120 KT ground speed a 3° gradient requires about 637 ft/min.

How does wind affect the descent plan?

Distance is calculated from gradient, descent speed from ground speed. With a headwind ground speed decreases and the descent speed needed for the same gradient falls; with a tailwind it increases. TOD distance does not change as long as the gradient stays constant, but descent time changes.

Why is a 3° glide path standard?

Standard approach glide paths are generally designed at 3° (approx. 5.2%); they suit aircraft performance, passenger comfort and stabilised approaches. ICAO PANS-OPS uses the nominal 3° glide path as its basis.

What should I do if I start descent late?

When you notice you are above the profile, increase descent speed and gradient early and in a controlled way, use speedbrakes or descent configuration within POH limits, or request extra distance from ATC (vectors, holding). A steep, fast approach leads to an unstable approach.

Why is a margin (deceleration allowance) added?

Descending to the fix to reduce speed to approach speed and configure requires distance. Bringing TOD forward a few NM leaves a horizontal segment for this.

Is the descent plan made with IAS, TAS or GS?

Distance and descent speed are calculated based on ground speed (GS), because distance is measured over the ground. IAS and TAS are only needed to find GS (see IAS · TAS · GS simulation).

Sources

More calculators