ILS Approach Simulator: LOC, GS and DA Decision

Fly an ILS approach to a fictional runway: follow your path on the plan view and side profile, and watch the localiser and glideslope needles on the ILS indicator. Capture the localiser with heading and vertical speed, intercept the glideslope from below and stay on the glide path. On reaching DA, land if the runway is visible and the approach is stable; otherwise go around.

IRATPLRadio NavigationGame mode
In short: How do you fly an ILS?

ILS (Instrument Landing System) is a precision approach system showing the runway centreline (localizer, 108.10–111.95 MHz) and the 3° glidepath (glideslope, 329.15–335.00 MHz). On the display, the vertical needle shows the localizer and the horizontal needle shows the glideslope; the target path is on the side the needle is on. The descent rate needed on a 3° glidepath is approximately ground speed × 5. At CAT I, DH is 200 ft: if the runway is not visible here or the approach is not stable, go around.

ILS · LOC / GS
VSI
Heading (HDG bug)
080
Vertical speed (VS, fpm)
0
Keyboard: ←→ heading ±5°, ↑↓ vertical speed ±100 fpm. The aircraft flies at 90 kt and turns to heading at standard rate (3°/s).
Height (RA)
To threshold
Ground speed
Required VS
What is happening now?

How does it work?

The localiser measures the aircraft's angle from the centreline using the antenna at the runway end; the course width is set so that it is 700 ft at the threshold. The glideslope compares the aircraft's elevation angle with 3° from the antenna slightly inside the threshold; full-scale deflection is ±0.7°. The aircraft flies at 90 kt and turns to heading at standard rate, and the vertical speed gently approaches the value you select. Wind changes both the track and the ground speed, and therefore the required descent rate. On the mission, when you reach the DA the simulation stops and asks for a decision.

Test yourself

ILS, DA/DH, stabilised approach and go-around questions often appear in IR and ATPL Radio Navigation and Flight Performance lessons.

Practice ATPL questions →

This simulator is for training only. Values are representative and do not replace the aircraft’s official POH/AFM, the AIP or current weather information in real flight operations. The pilot in command is always responsible.

ILS Approach Simulator: LOC, GS and DA Decision: the full explanation

Published: · Updated: · By: Son Yaklaşma editorial team

What is ILS?

ILS (Instrument Landing System) is a precision approach system that provides both horizontal and vertical guidance from within the cloud down to the runway. The localiser broadcasts the runway centreline, while the glideslope broadcasts the 3° descent path towards the threshold. The pilot selects the ILS frequency, confirms it by listening to the Morse identification code, and descends to the decision height while keeping the two needles centred on the indicator.

Components of ILS (FAA AIM 1-1-9)
ComponentWhat does it tell you?FrequencyAntenna
Localiser (LOC)Horizontal guidance: are you to the right or left of the runway centreline?108.10–111.95 MHz (odd tenths, 40 channels)Beyond the far end of the runway
Glideslope (GS)Vertical guidance: are you above or below the 3° descent path?329.15–335.00 MHz (paired with the LOC frequency, selected automatically)Approximately 300 m inside the threshold, at the runway edge
Distance informationHow far is it to the threshold?DME or marker (75 MHz)Varies by aerodrome

How is the indicator read?

On the ILS indicator, the vertical needle shows the localiser, and the horizontal needle shows the glideslope. Both needles answer the question "where is the target track?": if the vertical needle is to the right, the runway centreline is to the right, so turn right; if the horizontal needle is up, the descent path is above you, meaning you are low, so reduce the rate of descent. When the two needles cross in the centre, the aircraft is both on the centreline and on the descent path.

Calculating the 3° descent path

On the 3° path, you descend approximately 318 ft per nautical mile (in practice "300 ft/NM"). The required rate of descent depends on ground speed: VS ≈ ground speed × 5 (exact factor 5.3). A headwind reduces ground speed, so less descent is needed; a tailwind requires a higher rate of descent.

Distance to threshold and height above threshold on the 3° descent path (TCH 50 ft; roughly 300 ft/NM)
Distance to thresholdHeight of the descent path
1 NM≈ 368 ft
2 NM≈ 687 ft
3 NM≈ 1,005 ft
4 NM≈ 1,324 ft
5 NM≈ 1,642 ft
6 NM≈ 1,961 ft
Required rate of descent for a 3° descent (VS ≈ ground speed × 5.3)
Ground speedRate of descent
70 kt≈ 370 fpm
90 kt≈ 480 fpm
110 kt≈ 580 fpm
130 kt≈ 690 fpm
150 kt≈ 800 fpm

Why is the glideslope intercepted from below?

Due to the beam structure of the glideslope antenna, false descent paths may form above the true descent path, at steeper angles. In the standard technique, the aircraft flies level at the published intercept altitude, and descent begins as the glideslope needle moves down from above (approximately 1 dot before). This avoids false paths and allows a smooth transition onto the descent path.

Stabilised approach and the 1000 ft gate

According to the Flight Safety Foundation's recommendation, in instrument conditions the aircraft must be stabilised by 1000 ft at the latest: localiser and glideslope within 1 dot, rate of descent less than 1000 fpm, aircraft in landing configuration and speed on target. If these conditions are not met, the approach is not continued and a go-around is flown. The simulator also evaluates your status at 1000 ft separately.

DA, DH and the decision

DH (decision height) is the height above threshold, and DA (decision altitude) is the altitude read on the altimeter: DA = threshold elevation + DH. For CAT I ILS, DH is 200 ft; according to ICAO, visibility must be at least 800 m or RVR at least 550 m. If the required visual reference, such as the runway, threshold or approach lights, is not seen at DA, or the approach is not stable, you go around (missed approach) and fly the missed approach procedure. You do not descend below DA to "take one more look".

Worked example

RWY 05 ILS (track 050), TAS 90 kt, wind 020°/15 kt. The wind is coming from 30° left of the runway track: headwind component 15 × cos 30° ≈ 13 kt, crosswind component 15 × sin 30° ≈ 7.5 kt. Ground speed ≈ 90 − 13 = 77 kt, required descent ≈ 77 × 5.3 ≈ 410 fpm. To remain on centreline, the wind correction ≈ asin(7.5 / 90) ≈ 5° left, heading ≈ 045. At 3 NM the descent path is approximately 1000 ft; if the needles are within 1 dot, the approach is stable.

Common mistakes

The aerodrome and ILS in the simulator (ISYK 110.30, threshold 350 ft) are fictional. The aircraft flies at 90 kt; the geometry is set according to the values in FAA AIM 1-1-9. It is for training purposes only; in actual approaches, the published procedures and minima apply.

How is an ILS approach flown?

  1. Tune and identify the ILS. Enter the frequency, listen to the Morse code, set the course selector (CRS) to the runway heading.
  2. Intercept the localizer. Approach the centreline at an intercept angle of around 30°; once the needle starts to move, turn the heading to the runway track.
  3. Intercept the glideslope from below. At the capture altitude, level off; start descending when the GS needle is one dot below centre from above.
  4. Adjust the rate of descent. VS ≈ ground speed × 5; less with a headwind, more with a tailwind.
  5. Keep the pins centred. Make small corrections; at 1000 ft, the localiser and glideslope should be within 1 dot, and the descent should be less than 1000 fpm.
  6. Decide at DA. If a visual reference exists and the approach is stable, land; if not, go around and fly the missed approach procedure.

Frequently asked questions

What is ILS?

ILS is a precision approach system consisting of a localiser, which shows the runway centreline, and a glideslope, which shows the 3° descent path. It provides both lateral and vertical guidance from inside the cloud down to decision height.

What do the needles on the ILS indicator show?

The vertical needle shows the localizer and the horizontal needle shows the glideslope. The target track is on the side the needle is on: if the vertical needle is to the right, the centreline is to the right; if the horizontal needle is up, the glidepath is above (the aircraft is low).

How many degrees is one dot on the ILS?

The localiser course width is set so that it is 700 ft at the threshold; in angle terms it is usually between 3–6°, and at the threshold each dot is approximately 70 ft. On the glideslope, full deflection is ±0.7°, and each dot is approximately 0.14°.

How is the descent rate calculated for a 3° glide path?

Descent rate ≈ ground speed × 5 (exact factor 5.3). For example, at a ground speed of 90 kt, about 480 fpm is needed. Roughly 300 ft is lost per mile: at 3 NM from the threshold, the glidepath is at about 1000 ft.

What is the difference between DH and DA?

DH is the height above threshold elevation (200 ft for CAT I); DA is the altitude read on the altimeter and equals threshold elevation plus DH. If the threshold is 350 ft, DA is 550 ft.

Why is the glideslope intercepted from below?

False glidepaths can form at steeper angles above the true glidepath. Flying level at the intercept altitude and starting descent as the needle comes down from above eliminates this risk.

What should you do if the runway is not visible at DA?

Go around: climb and fly the published missed approach procedure. If the approach is not stable, make the same decision even if visual reference is available.

Are my results being saved?

The simulator is open to everyone. To see your stars in approach missions, simply sign up for free and log in.

Sources

More calculators