Altimeter Setting Simulator: QNH, QFE and QNE

An altimeter does not measure altitude directly: it shows height above the pressure level you set. Switch between QNH, QFE and QNE and see the same aircraft read different values, and how far it is below or above the indication when the setting is wrong.

PPLInstrumentsBeginner
In short: What is the difference between QNH, QFE and QNE?

With QNH set the altimeter reads altitude above mean sea level; with QFE it reads height above the airfield (zero on the runway); with the standard setting of 1013.25 hPa (QNE) it reads pressure altitude, used for flight levels. Each hPa of error is about 27–30 ft.

1 000 ft
1013 hPa
2 000 ft
Altimeter setting
1013.0 hPa
Drag to set it by hand.
Preset scenarios
Altimeter reading
—ft
True altitude (MSL)
—ft
Height above airfield
—ft
Setting error
—ft
—

Where is the datum?

The altimeter shows height above the pressure level you set

One aircraft, three settings

What each setting reads at the same moment
QNH
—
hPa · reduced to sea level
QFE
—
hPa · pressure at airfield level
QNE
1013.25
hPa · standard setting
1 hPa
—
ft · approx. at this altitude

How does it work?

An altimeter is a barometer: it measures static pressure and converts it to altitude using the standard atmosphere. The subscale sets which pressure level counts as zero: with QNH it reads altitude above sea level, with QFE height above the airfield and with 1013.25 hPa (QNE) pressure altitude.

If the setting is higher than the actual QNH the altimeter over-reads and the aircraft is lower than indicated (about 27–30 ft per hPa). The simulator assumes ISA temperature, so it does not include the cold-temperature error.

Test yourself

Airfield elevation 1,000 ft, actual QNH 990 hPa, subscale left at 1013: how many feet does the altimeter over-read? Estimate first, then check it in the simulator.

Practice ATPL questions →

This simulator is for training only. Values are representative and do not replace the aircraft’s official POH/AFM, the AIP or current weather information in real flight operations. The pilot in command is always responsible.

Altimeter Setting Simulator: QNH, QFE and QNE: the full explanation

Published: · Updated: · By: Son Yaklaşma editorial team

QNH, QFE and QNE

What a wrong setting does

Every hPa of error moves the reading by roughly 27–30 ft near sea level. If the subscale is set higher than the actual QNH, the altimeter over-reads and the aircraft is lower than indicated: “high to low, look out below”.

Altimeter reading for an aircraft at 3,000 ft MSL with an actual QNH of 1013.25 hPa, for different subscale settings
SubscaleSettingAltimeter readsError
1,013.25 hPaCorrect (QNH 1013)3,000 ft0 ft
1,003.25 hPa10 hPa too low2,726 ft−274 ft
1,023.25 hPa10 hPa too high3,272 ft272 ft

Worked example

You fly from a 1013 hPa area into a low with an actual QNH of 990 hPa and forget to reset the altimeter. At a true altitude of 3,000 ft the altimeter reads about 3,641 ft: you are roughly 641 ft lower than you think, which is exactly how terrain clearance is lost.

Transition altitude and level

Climbing through the transition altitude you set 1013 and fly flight levels; descending through the transition level you set the local QNH. In Turkey the transition altitude is published per aerodrome in the AIP. The simulator assumes ISA temperature, so it does not show the extra cold-temperature error (“high to low” applies to temperature too).

How to set the altimeter correctly

  1. Get the QNH. Take the current QNH from the ATIS, the tower or the METAR (the Q group, e.g. Q1008).
  2. Set it on the subscale. Turn the knob until the Kollsman window shows the QNH; on the ground the altimeter should read airfield elevation.
  3. Cross-check on the ground. If the reading differs from the airfield elevation by more than the allowed tolerance, do not rely on the instrument.
  4. Climb through the transition altitude. Set 1013.25 hPa (29.92 inHg) and fly flight levels.
  5. Descend through the transition level. Set the destination QNH given by ATC or the ATIS.

Frequently asked questions

What is QNH?

QNH is the airfield pressure reduced to mean sea level using the standard atmosphere. With QNH set the altimeter reads altitude above mean sea level and shows the airfield elevation on the ground.

What is QFE?

QFE is the atmospheric pressure at airfield level. With QFE set the altimeter reads height above the airfield and shows zero on the runway. It is less common today but still used in some countries and by the military.

What is QNE?

QNE is the altimeter reading (pressure altitude) at the airfield with the standard setting of 1013.25 hPa. In practice “setting QNE” means setting 1013.25 hPa / 29.92 inHg to fly flight levels.

What does “high to low, look out below” mean?

Flying from high pressure to low pressure without resetting the altimeter makes it over-read, so the aircraft is lower than indicated. The same applies when flying from warm into cold air.

How many feet is 1 hPa?

Near sea level about 27–30 ft per hPa (often rounded to 30 ft). At higher altitudes each hPa corresponds to more feet.

Sources

More calculators